{
	"type": "machine",
	"setting_id": "GM_Anycubic_006",
	"name": "Anycubic Kobra 2 0.4 nozzle",
	"from": "system",
	"instantiation": "true",
	"inherits": "fdm_machine_common",
	"printer_model": "Anycubic Kobra 2",
	"default_print_profile": "0.20mm Standard @Anycubic Kobra2",
	"nozzle_diameter": [
		"0.4"
	],
	"printable_area": [
		"0x0",
		"220x0",
		"220x220",
		"0x220"
	],
	"printable_height": "250",
	"nozzle_type": "undefine",
	"auxiliary_fan": "0",
	"machine_max_acceleration_extruding": [
		"2500",
		"2500"
	],
	"machine_max_acceleration_retracting": [
		"2500",
		"2500"
	],
	"machine_max_acceleration_travel": [
		"3000",
		"1250"
	],
	"machine_max_acceleration_x": [
		"2500",
		"2500"
	],
	"machine_max_acceleration_y": [
		"2500",
		"2500"
	],
	"machine_max_acceleration_z": [
		"800",
		"800"
	],
	"machine_max_speed_e": [
		"80",
		"80"
	],
	"machine_max_speed_x": [
		"300",
		"300"
	],
	"machine_max_speed_y": [
		"250",
		"250"
	],
	"machine_max_speed_z": [
		"8",
		"8"
	],
	"machine_max_jerk_e": [
		"10",
		"10"
	],
	"machine_max_jerk_x": [
		"15",
		"15"
	],
	"machine_max_jerk_y": [
		"10",
		"10"
	],
	"machine_max_jerk_z": [
		"2",
		"2"
	],
	"max_layer_height": [
		"0.32"
	],
	"min_layer_height": [
		"0.04"
	],
	"printer_settings_id": "Anycubic",
	"retraction_minimum_travel": [
		"1"
	],
	"retract_before_wipe": [
		"70%"
	],
	"retraction_length": [
		"2"
	],
	"retract_length_toolchange": [
		"1"
	],
	"retraction_speed": [
		"80"
	],
	"deretraction_speed": [
		"80"
	],
	"single_extruder_multi_material": "0",
	"change_filament_gcode": "M600",
	"machine_pause_gcode": "M601",
	"default_filament_profile": [
		"Anycubic Generic PLA"
	],
	"machine_start_gcode": "G90 ;Use absolute coordinates\nM83 ;Extruder relative mode\nM104 S[first_layer_temperature] ;Set extruder temp\nM140 S[first_layer_bed_temperature] ;Set bed temp\nM190 S[first_layer_bed_temperature] ;Wait for bed temp\nM109 S[first_layer_temperature] ;Wait for extruder temp\nG28 ;Move X/Y/Z to min endstops\nG1 Z0.28 ;Lift nozzle a bit\nG92 E0 ;Specify current extruder position as zero\nG1 Y3 F1800 ;Move Y to purge point\nG1 X60 E25 F500 ;Extrude 25mm of filament in a 5cm line\nG92 E0 ;Zero the extruded length again\nG1 E-2 F500 ;Retract a little\nG1 X70 F4000 ;Quickly wipe away from the filament line\nM117",
	"machine_end_gcode": "M104 S0 ;Extruder off\nM140 S0 ;Heatbed off\nM107 ;Fan off\nG91 ;Relative positioning\nG1 E-5 F3000 ;Retract filament\nG1 Z+0.3 F3000 ;Lift print head\nG28 X0 F3000 ;Home X axis\nM84 ;Disable stepper motors",
	"before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\n[layer_num] @ [layer_z]mm",
	"layer_change_gcode": ";AFTER_LAYER_CHANGE\n[layer_num] @ [layer_z]mm",
	"scan_first_layer": "0"
}