{
  "setting_id": "GM003",
  "name": "Kingroon KP3S 3.0 0.4 nozzle",
  "instantiation": "true",
  "inherits": "fdm_machine_common",
  "printer_model": "Kingroon KP3S 3.0",
  "default_print_profile": "0.30mm Standard @Kingroon KP3S 3.0",
  "machine_end_gcode": "G1 E-1.0 F2100 ; retract\nG92 E0.0\nG1{if max_layer_z < max_print_height} Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} E-34.0 F720 ; move print head up & retract filament\nG4 ; wait\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nG1 X0 Y105 F3000 ; park print head\nM84 ; disable motors",
  "machine_start_gcode": "G90 ; use absolute coordinates\nM83 ; extruder relative mode\nM204 S[machine_max_acceleration_extruding] T[machine_max_acceleration_retracting]\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nG28 ; home all\nG1 Y1.0 Z0.3 F1000 ; move print head up\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG92 E0.0\n; initial load\n M117 Purge extruder\n G1 X2 Y20 Z0.3 F5000.0 ; move to start-line position\n G1 X2 Y175.0 Z0.3 F1500.0 E15 ; draw 1st line\n G1 X2 Y175.0 Z0.4 F5000.0 ; move to side a little\n G1 X2 Y20 Z0.4 F1500.0 E30 ; draw 2nd line\n G92 E0 ; reset extruder\n G1 Z1.0 F3000 ; move z up little to prevent scratching of surface",
  "type": "machine",
  "nozzle_diameter": ["0.4"],
  "cooling_tube_length": "0",
  "cooling_tube_retraction": "0",
  "enable_filament_ramming": "0",
  "extra_loading_move": "0",
  "fan_speedup_overhangs": "0",
  "fan_speedup_time": "1",
  "from": "system",
  "machine_max_acceleration_e": [
      "10000",
      "5000"
  ],
  "machine_max_acceleration_extruding": [
      "10000",
      "9000"
  ],
  "machine_max_acceleration_retracting": [
      "10000",
      "9000"
  ],
  "machine_max_acceleration_x": [
      "4000",
      "9000"
  ],
  "machine_max_acceleration_y": [
      "4000",
      "9000"
  ],
  "machine_max_acceleration_z": [
      "1100",
      "100"
  ],
  "machine_max_speed_e": [
      "50",
      "60"
  ],
  "machine_max_speed_x": [
      "300",
      "200"
  ],
  "machine_max_speed_y": [
      "300",
      "200"
  ],
  "machine_max_speed_z": [
      "30",
      "12"
  ],
  "manual_filament_change": "1",
  "min_layer_height": [
      "0.1"
  ],
  "nozzle_type": "brass",
  "parking_pos_retraction": "0",
  "printable_area": [
      "0x0",
      "180x0",
      "180x180",
      "0x180"
  ],
  "printable_height": "180",
  "purge_in_prime_tower": "0",
  "retract_length_toolchange": [
      "0.5"
  ],
  "retract_when_changing_layer": [
      "1"
  ],
  "retraction_length": [
      "0.3"
  ],
  "retraction_minimum_travel": [
      "3"
  ],
  "retraction_speed": [
      "30"
  ],
  "support_air_filtration": "0",
  "support_chamber_temp_control": "0",
  "wipe": [
      "1"
  ],
  "z_hop": [
      "0.2"
  ]
}