# generated by Slic3r Prusa Edition 1.38.4 on 2017-12-10 at 09:05:01

[print:0.05mm DETAIL]
avoid_crossing_perimeters = 0
bottom_solid_layers = 10
bridge_acceleration = 300
bridge_angle = 0
bridge_flow_ratio = 0.7
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 MM Single Mode"
complete_objects = 0
default_acceleration = 500
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 20
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 25%
fill_pattern = cubic
first_layer_acceleration = 500
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 800
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.5
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 30
interface_shells = 0
layer_height = 0.05
max_print_speed = 80
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 300
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 30
perimeters = 3
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 1
small_perimeter_speed = 15
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 30
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.3
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 1.5
support_material_speed = 30
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 60%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.45
top_solid_infill_speed = 20
top_solid_layers = 15
travel_speed = 180
wipe_tower = 0
wipe_tower_per_color_wipe = 15
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.05mm DETAIL 0.25 nozzle]
avoid_crossing_perimeters = 0
bottom_solid_layers = 10
bridge_acceleration = 300
bridge_angle = 0
bridge_flow_ratio = 0.7
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK2 0.25 nozzle";"Original Prusa i3 MK2 MM Single Mode 0.25 nozzle"
complete_objects = 0
default_acceleration = 500
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 20
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.28
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 500
first_layer_extrusion_width = 0.3
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 800
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 20
interface_shells = 0
layer_height = 0.05
max_print_speed = 100
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 300
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 20
perimeters = 4
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 1
small_perimeter_speed = 10
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.18
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0.15
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 1
support_material_speed = 20
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 150%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 20
top_solid_layers = 15
travel_speed = 200
wipe_tower = 0
wipe_tower_per_color_wipe = 15
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.05mm DETAIL MK3]
avoid_crossing_perimeters = 0
bottom_solid_layers = 10
bridge_acceleration = 300
bridge_angle = 0
bridge_flow_ratio = 0.7
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK3"
complete_objects = 0
default_acceleration = 500
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 20
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 25%
fill_pattern = cubic
first_layer_acceleration = 500
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 800
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.5
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 30
interface_shells = 0
layer_height = 0.05
max_print_speed = 80
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 300
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 30
perimeters = 3
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 1
small_perimeter_speed = 15
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 30
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.3
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 1.5
support_material_speed = 30
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 60%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.45
top_solid_infill_speed = 20
top_solid_layers = 15
travel_speed = 180
wipe_tower = 0
wipe_tower_per_color_wipe = 15
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.10mm DETAIL]
avoid_crossing_perimeters = 0
bottom_solid_layers = 7
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.7
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 MM Single Mode"
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 2000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 60
interface_shells = 0
layer_height = 0.1
max_print_speed = 100
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 50
perimeters = 3
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 1
small_perimeter_speed = 20
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 50
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 50
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 60%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.45
top_solid_infill_speed = 40
top_solid_layers = 9
travel_speed = 120
wipe_tower = 0
wipe_tower_per_color_wipe = 15
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.10mm DETAIL 0.25 nozzle]
avoid_crossing_perimeters = 0
bottom_solid_layers = 7
bridge_acceleration = 600
bridge_angle = 0
bridge_flow_ratio = 0.7
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK2 0.25 nozzle";"Original Prusa i3 MK2 MM Single Mode 0.25 nozzle"
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.25
external_perimeter_speed = 20
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.25
fill_angle = 45
fill_density = 15%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.25
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 1600
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.25
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 40
interface_shells = 0
layer_height = 0.1
max_print_speed = 100
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 600
perimeter_extruder = 1
perimeter_extrusion_width = 0.25
perimeter_speed = 25
perimeters = 4
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 1
small_perimeter_speed = 10
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.25
solid_infill_speed = 40
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.18
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0.15
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 1
support_material_speed = 50
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 150%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.25
top_solid_infill_speed = 30
top_solid_layers = 9
travel_speed = 120
wipe_tower = 0
wipe_tower_per_color_wipe = 15
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.10mm DETAIL MK3]
avoid_crossing_perimeters = 0
bottom_solid_layers = 4
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.8
bridge_speed = 30
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK3"
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 3500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 35%
infill_speed = 200
interface_shells = 0
layer_height = 0.1
max_print_speed = 250
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 60
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 1
small_perimeter_speed = 20
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 200
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 50
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 60%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 50
top_solid_layers = 5
travel_speed = 250
wipe_tower = 0
wipe_tower_per_color_wipe = 15
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.15mm 100mms Linear Advance]
avoid_crossing_perimeters = 0
bottom_solid_layers = 4
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.95
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 MM Single Mode";"Original Prusa i3 MK2 MultiMaterial"
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 50
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 2000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 100
interface_shells = 0
layer_height = 0.15
max_print_speed = 150
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 60
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 100
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 60
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 60%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 70
top_solid_layers = 5
travel_speed = 120
wipe_tower = 1
wipe_tower_per_color_wipe = 15
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.15mm OPTIMAL]
avoid_crossing_perimeters = 0
bottom_solid_layers = 5
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.8
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 MM Single Mode";"Original Prusa i3 MK2 MultiMaterial"
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 2000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 60
interface_shells = 0
layer_height = 0.15
max_print_speed = 100
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 50
perimeters = 3
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 1
small_perimeter_speed = 20
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 50
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 50
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 60%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.45
top_solid_infill_speed = 40
top_solid_layers = 7
travel_speed = 120
wipe_tower = 1
wipe_tower_per_color_wipe = 15
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.15mm OPTIMAL 0.25 nozzle]
avoid_crossing_perimeters = 0
bottom_solid_layers = 5
bridge_acceleration = 600
bridge_angle = 0
bridge_flow_ratio = 0.7
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK2 0.25 nozzle";"Original Prusa i3 MK2 MM Single Mode 0.25 nozzle";"Original Prusa i3 MK2 MultiMaterial 0.25 nozzle"
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.25
external_perimeter_speed = 20
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.25
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.25
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 1600
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.25
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 40
interface_shells = 0
layer_height = 0.15
max_print_speed = 100
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 600
perimeter_extruder = 1
perimeter_extrusion_width = 0.25
perimeter_speed = 25
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 1
small_perimeter_speed = 10
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.25
solid_infill_speed = 40
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.2
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0.15
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 1
support_material_speed = 50
support_material_synchronize_layers = 0
support_material_threshold = 35
support_material_with_sheath = 0
support_material_xy_spacing = 150%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.25
top_solid_infill_speed = 30
top_solid_layers = 7
travel_speed = 120
wipe_tower = 1
wipe_tower_per_color_wipe = 15
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.15mm OPTIMAL 0.6 nozzle]
avoid_crossing_perimeters = 0
bottom_solid_layers = 5
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.8
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK2 0.6 nozzle";"Original Prusa i3 MK2 MM Single Mode 0.6 nozzle";"Original Prusa i3 MK2 MultiMaterial 0.6 nozzle"
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.61
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.67
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.65
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 2000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.75
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 60
interface_shells = 0
layer_height = 0.15
max_print_speed = 100
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.65
perimeter_speed = 50
perimeters = 3
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 1
small_perimeter_speed = 20
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.65
solid_infill_speed = 50
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 50
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 60%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.6
top_solid_infill_speed = 40
top_solid_layers = 7
travel_speed = 120
wipe_tower = 1
wipe_tower_per_color_wipe = 15
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.15mm OPTIMAL MK3]
avoid_crossing_perimeters = 0
bottom_solid_layers = 4
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.8
bridge_speed = 30
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK3"
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 3500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 35%
infill_speed = 200
interface_shells = 0
layer_height = 0.15
max_print_speed = 250
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 60
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 1
small_perimeter_speed = 20
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 200
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 50
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 60%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 50
top_solid_layers = 5
travel_speed = 250
wipe_tower = 1
wipe_tower_per_color_wipe = 15
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.15mm OPTIMAL SOLUBLE FULL]
avoid_crossing_perimeters = 0
bottom_solid_layers = 5
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.8
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK2 MultiMaterial"
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 25
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 2000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 60
interface_shells = 0
layer_height = 0.15
max_print_speed = 100
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = Set your solluble extruder in Multiple Extruders > Support material/raft/skirt extruder &  Support material/raft interface extruder
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 40
perimeters = 3
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 0
small_perimeter_speed = 20
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 40
spiral_vase = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0
support_material_enforce_layers = 0
support_material_extruder = 4
support_material_extrusion_width = 0.45
support_material_interface_contact_loops = 0
support_material_interface_extruder = 4
support_material_interface_layers = 2
support_material_interface_spacing = 0.1
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 50
support_material_synchronize_layers = 1
support_material_threshold = 80
support_material_with_sheath = 1
support_material_xy_spacing = 60%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.45
top_solid_infill_speed = 30
top_solid_layers = 7
travel_speed = 120
wipe_tower = 1
wipe_tower_per_color_wipe = 20
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.15mm OPTIMAL SOLUBLE INTERFACE]
avoid_crossing_perimeters = 0
bottom_solid_layers = 5
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.8
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK2 MultiMaterial"
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 25
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 2000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 60
interface_shells = 0
layer_height = 0.15
max_print_speed = 100
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = Set your solluble extruder in Multiple Extruders >  Support material/raft interface extruder
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 40
perimeters = 3
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 0
small_perimeter_speed = 20
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 40
spiral_vase = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.45
support_material_interface_contact_loops = 0
support_material_interface_extruder = 4
support_material_interface_layers = 3
support_material_interface_spacing = 0.1
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 50
support_material_synchronize_layers = 1
support_material_threshold = 80
support_material_with_sheath = 0
support_material_xy_spacing = 120%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.45
top_solid_infill_speed = 30
top_solid_layers = 7
travel_speed = 120
wipe_tower = 1
wipe_tower_per_color_wipe = 20
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.20mm 100mms Linear Advance]
avoid_crossing_perimeters = 0
bottom_solid_layers = 4
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.95
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 MM Single Mode";"Original Prusa i3 MK2 MultiMaterial"
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 50
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 2000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 100
interface_shells = 0
layer_height = 0.2
max_print_speed = 150
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 60
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 1
small_perimeter_speed = 30
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 100
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 60
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 60%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 70
top_solid_layers = 5
travel_speed = 120
wipe_tower = 1
wipe_tower_per_color_wipe = 15
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.20mm NORMAL]
avoid_crossing_perimeters = 0
bottom_solid_layers = 4
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.95
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 MM Single Mode";"Original Prusa i3 MK2 MultiMaterial"
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 2000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 60
interface_shells = 0
layer_height = 0.2
max_print_speed = 100
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 50
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 1
small_perimeter_speed = 20
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 50
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 50
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 60%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 40
top_solid_layers = 5
travel_speed = 120
wipe_tower = 1
wipe_tower_per_color_wipe = 15
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.20mm NORMAL 0.6 nozzle]
avoid_crossing_perimeters = 0
bottom_solid_layers = 4
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.8
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK2 0.6 nozzle";"Original Prusa i3 MK2 MM Single Mode 0.6 nozzle";"Original Prusa i3 MK2 MultiMaterial 0.6 nozzle"
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.61
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.67
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.65
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 2000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.75
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 60
interface_shells = 0
layer_height = 0.2
max_print_speed = 100
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.65
perimeter_speed = 50
perimeters = 3
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 1
small_perimeter_speed = 20
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.65
solid_infill_speed = 50
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 50
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 60%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.6
top_solid_infill_speed = 40
top_solid_layers = 5
travel_speed = 120
wipe_tower = 1
wipe_tower_per_color_wipe = 15
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.20mm NORMAL MK3]
avoid_crossing_perimeters = 0
bottom_solid_layers = 4
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.8
bridge_speed = 30
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK3"
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 3500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 35%
infill_speed = 200
interface_shells = 0
layer_height = 0.2
max_print_speed = 250
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 60
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 1
small_perimeter_speed = 20
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 200
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 50
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 60%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 50
top_solid_layers = 5
travel_speed = 250
wipe_tower = 1
wipe_tower_per_color_wipe = 15
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.20mm NORMAL SOLUBLE FULL]
avoid_crossing_perimeters = 0
bottom_solid_layers = 4
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.95
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK2 MultiMaterial"
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 30
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 2000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 60
interface_shells = 0
layer_height = 0.2
max_print_speed = 100
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = Set your solluble extruder in Multiple Extruders > Support material/raft/skirt extruder &  Support material/raft interface extruder
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 40
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 0
small_perimeter_speed = 20
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 40
spiral_vase = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0
support_material_enforce_layers = 0
support_material_extruder = 4
support_material_extrusion_width = 0.45
support_material_interface_contact_loops = 0
support_material_interface_extruder = 4
support_material_interface_layers = 2
support_material_interface_spacing = 0.1
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 50
support_material_synchronize_layers = 1
support_material_threshold = 80
support_material_with_sheath = 1
support_material_xy_spacing = 120%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 30
top_solid_layers = 5
travel_speed = 120
wipe_tower = 1
wipe_tower_per_color_wipe = 20
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.20mm NORMAL SOLUBLE INTERFACE]
avoid_crossing_perimeters = 0
bottom_solid_layers = 4
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.95
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK2 MultiMaterial"
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 30
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 2000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 60
interface_shells = 0
layer_height = 0.2
max_print_speed = 100
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = Set your solluble extruder in Multiple Extruders >  Support material/raft interface extruder
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 40
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 0
small_perimeter_speed = 20
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 40
spiral_vase = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.45
support_material_interface_contact_loops = 0
support_material_interface_extruder = 4
support_material_interface_layers = 3
support_material_interface_spacing = 0.1
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 50
support_material_synchronize_layers = 1
support_material_threshold = 80
support_material_with_sheath = 0
support_material_xy_spacing = 120%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 30
top_solid_layers = 5
travel_speed = 120
wipe_tower = 1
wipe_tower_per_color_wipe = 20
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.35mm FAST]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.95
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 MM Single Mode";"Original Prusa i3 MK2 MultiMaterial"
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.6
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 2000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.7
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 60
interface_shells = 0
layer_height = 0.35
max_print_speed = 100
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.43
perimeter_speed = 50
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 1
small_perimeter_speed = 20
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.7
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 50
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 60%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.43
top_solid_infill_speed = 50
top_solid_layers = 4
travel_speed = 120
wipe_tower = 1
wipe_tower_per_color_wipe = 15
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.35mm FAST 0.6 nozzle]
avoid_crossing_perimeters = 0
bottom_solid_layers = 7
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.8
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK2 0.6 nozzle";"Original Prusa i3 MK2 MM Single Mode 0.6 nozzle";"Original Prusa i3 MK2 MultiMaterial 0.6 nozzle"
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.61
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.67
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.65
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 2000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.75
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 60
interface_shells = 0
layer_height = 0.35
max_print_speed = 100
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.65
perimeter_speed = 50
perimeters = 3
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 1
small_perimeter_speed = 20
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.65
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 50
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 60%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.6
top_solid_infill_speed = 50
top_solid_layers = 9
travel_speed = 120
wipe_tower = 1
wipe_tower_per_color_wipe = 15
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.35mm FAST MK3]
avoid_crossing_perimeters = 0
bottom_solid_layers = 4
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.8
bridge_speed = 30
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK3"
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.6
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 3500
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.7
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 35%
infill_speed = 200
interface_shells = 0
layer_height = 0.35
max_print_speed = 250
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 0
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_speed = 60
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 1
small_perimeter_speed = 20
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.7
solid_infill_speed = 200
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 50
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 60%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.45
top_solid_infill_speed = 50
top_solid_layers = 4
travel_speed = 250
wipe_tower = 1
wipe_tower_per_color_wipe = 15
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.35mm FAST sol full 0.6 nozzle]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.8
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK2 MultiMaterial 0.6 nozzle"
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.6
external_perimeter_speed = 30
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.67
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.65
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 2000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.75
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 60
interface_shells = 0
layer_height = 0.35
max_print_speed = 100
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = Set your solluble extruder in Multiple Extruders >  Support material/raft interface extruder
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.65
perimeter_speed = 40
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 0
small_perimeter_speed = 20
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.65
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0
support_material_enforce_layers = 0
support_material_extruder = 4
support_material_extrusion_width = 0.55
support_material_interface_contact_loops = 0
support_material_interface_extruder = 4
support_material_interface_layers = 3
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 50
support_material_synchronize_layers = 1
support_material_threshold = 80
support_material_with_sheath = 0
support_material_xy_spacing = 120%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.57
top_solid_infill_speed = 50
top_solid_layers = 4
travel_speed = 120
wipe_tower = 1
wipe_tower_per_color_wipe = 20
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:0.35mm FAST sol int 0.6 nozzle]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.8
bridge_speed = 20
brim_width = 0
clip_multipart_objects = 1
compatible_printers = "Original Prusa i3 MK2 MultiMaterial 0.6 nozzle"
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.6
external_perimeter_speed = 30
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.67
fill_angle = 45
fill_density = 20%
fill_pattern = cubic
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.65
first_layer_height = 0.2
first_layer_speed = 30
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 2000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.75
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 60
interface_shells = 0
layer_height = 0.35
max_print_speed = 100
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 4
notes = Set your solluble extruder in Multiple Extruders >  Support material/raft interface extruder
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.65
perimeter_speed = 40
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = nearest
skirt_distance = 2
skirt_height = 3
skirts = 0
small_perimeter_speed = 20
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.65
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.55
support_material_interface_contact_loops = 0
support_material_interface_extruder = 4
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 50
support_material_synchronize_layers = 1
support_material_threshold = 80
support_material_with_sheath = 0
support_material_xy_spacing = 150%
thin_walls = 0
threads = 4
top_infill_extrusion_width = 0.57
top_solid_infill_speed = 50
top_solid_layers = 4
travel_speed = 120
wipe_tower = 1
wipe_tower_per_color_wipe = 20
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[filament:ColorFabb Brass Bronze  1.75mm]
bed_temperature = 60
bridge_fan_speed = 100
compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 0.6 nozzle";"Original Prusa i3 MK2 MM Single Mode";"Original Prusa i3 MK2 MM Single Mode 0.6 nozzle";"Original Prusa i3 MK2 MultiMaterial";"Original Prusa i3 MK2 MultiMaterial 0.6 nozzle";"Original Prusa i3 MK3"
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1.3
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #804040
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 60
first_layer_temperature = 210
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}10{endif}; Filament gcode"
temperature = 210

[filament:ColorFabb HT 1.75mm]
bed_temperature = 105
bridge_fan_speed = 30
compatible_printers = 
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 10
filament_colour = #FF8000
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 105
first_layer_temperature = 270
max_fan_speed = 20
min_fan_speed = 10
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}45{endif}; Filament gcode"
temperature = 270

[filament:ColorFabb PLA-PHA]
bed_temperature = 60
bridge_fan_speed = 100
compatible_printers = 
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #FF3232
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 15
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nDas Filament\nEsun PLA\nEUMAKERS PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nVerbatim PLA\nVerbatim BVOH"
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 60
first_layer_temperature = 215
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 15
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
temperature = 210

[filament:ColorFabb Woodfil 1.75mm]
bed_temperature = 60
bridge_fan_speed = 100
compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 0.6 nozzle";"Original Prusa i3 MK2 MM Single Mode";"Original Prusa i3 MK2 MM Single Mode 0.6 nozzle";"Original Prusa i3 MK2 MultiMaterial";"Original Prusa i3 MK2 MultiMaterial 0.6 nozzle";"Original Prusa i3 MK3"
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1.2
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #804040
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 60
first_layer_temperature = 200
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}10{endif}; Filament gcode"
temperature = 200

[filament:ColorFabb XT 1.75mm]
bed_temperature = 65
bridge_fan_speed = 50
compatible_printers = 
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #FF8000
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 90
first_layer_temperature = 240
max_fan_speed = 50
min_fan_speed = 30
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}45{endif}; Filament gcode"
temperature = 240

[filament:ColorFabb XT-CF20 1.75mm]
bed_temperature = 90
bridge_fan_speed = 50
compatible_printers = 
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1.2
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #804040
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 1
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = PET
first_layer_bed_temperature = 90
first_layer_temperature = 260
max_fan_speed = 50
min_fan_speed = 30
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
temperature = 260

[filament:ColorFabb nGen 1.75mm]
bed_temperature = 85
bridge_fan_speed = 40
compatible_printers = 
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 10
filament_colour = #FF8000
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = NGEN
first_layer_bed_temperature = 85
first_layer_temperature = 240
max_fan_speed = 35
min_fan_speed = 20
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}45{endif}; Filament gcode"
temperature = 240

[filament:ColorFabb nGen flex]
bed_temperature = 85
bridge_fan_speed = 40
compatible_printers = 
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 10
filament_colour = #FF8000
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 5
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = FLEX
first_layer_bed_temperature = 85
first_layer_temperature = 260
max_fan_speed = 35
min_fan_speed = 20
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}10{endif}; Filament gcode"
temperature = 260

[filament:E3D Edge]
bed_temperature = 90
bridge_fan_speed = 50
compatible_printers = 
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #FF8000
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = "List of manufacturers tested with standart PET print settings for MK2:\n\nE3D Edge\nFillamentum CPE GH100\nPlasty Mladeč PETG"
filament_settings_id = 
filament_soluble = 0
filament_type = PET
first_layer_bed_temperature = 85
first_layer_temperature = 230
max_fan_speed = 50
min_fan_speed = 30
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}45{endif}; Filament gcode"
temperature = 240

[filament:E3D PC-ABS 1.75mm]
bed_temperature = 100
bridge_fan_speed = 30
compatible_printers = 
cooling = 0
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #3A80CA
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 13
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 100
first_layer_temperature = 270
max_fan_speed = 30
min_fan_speed = 10
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
temperature = 270

[filament:Fillamentum ABS 1.75mm]
bed_temperature = 100
bridge_fan_speed = 30
compatible_printers = 
cooling = 0
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #3A80CA
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 13
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = ABS
first_layer_bed_temperature = 100
first_layer_temperature = 240
max_fan_speed = 30
min_fan_speed = 10
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
temperature = 240

[filament:Fillamentum ASA 1.75mm]
bed_temperature = 100
bridge_fan_speed = 30
compatible_printers = 
cooling = 0
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #3A80CA
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 13
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 100
first_layer_temperature = 265
max_fan_speed = 30
min_fan_speed = 10
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
temperature = 265

[filament:Fillamentum CPE HG100 HM100]
bed_temperature = 90
bridge_fan_speed = 50
compatible_printers = 
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #FF8000
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = "CPE HG100 , CPE HM100"
filament_settings_id = 
filament_soluble = 0
filament_type = PET
first_layer_bed_temperature = 90
first_layer_temperature = 260
max_fan_speed = 80
min_fan_speed = 80
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}45{endif}; Filament gcode"
temperature = 260

[filament:Fillamentum Timberfil]
bed_temperature = 60
bridge_fan_speed = 100
compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 0.6 nozzle";"Original Prusa i3 MK2 MM Single Mode";"Original Prusa i3 MK2 MM Single Mode 0.6 nozzle";"Original Prusa i3 MK2 MultiMaterial";"Original Prusa i3 MK2 MultiMaterial 0.6 nozzle";"Original Prusa i3 MK3"
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1.2
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #804040
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 60
first_layer_temperature = 190
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 15
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}10{endif}; Filament gcode"
temperature = 190

[filament:Generic ABS 1.75mm]
bed_temperature = 100
bridge_fan_speed = 30
compatible_printers = 
cooling = 0
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #3A80CA
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 13
filament_notes = "List of materials tested with standart ABS print settings for MK2:\n\nEsun ABS\nFil-A-Gehr ABS\nHatchboxABS\nPlasty Mladeč ABS"
filament_settings_id = 
filament_soluble = 0
filament_type = ABS
first_layer_bed_temperature = 100
first_layer_temperature = 255
max_fan_speed = 30
min_fan_speed = 10
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
temperature = 255

[filament:Generic PET 1.75mm]
bed_temperature = 90
bridge_fan_speed = 50
compatible_printers = 
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #FF8000
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = "List of manufacturers tested with standart PET print settings for MK2:\n\nE3D Edge\nFillamentum CPE GH100\nPlasty Mladeč PETG"
filament_settings_id = 
filament_soluble = 0
filament_type = PET
first_layer_bed_temperature = 85
first_layer_temperature = 230
max_fan_speed = 50
min_fan_speed = 30
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}45{endif}; Filament gcode"
temperature = 240

[filament:Generic PLA 1.75mm]
bed_temperature = 60
bridge_fan_speed = 100
compatible_printers = 
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #FF3232
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 15
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nDas Filament\nEsun PLA\nEUMAKERS PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nVerbatim PLA\nVerbatim BVOH"
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 60
first_layer_temperature = 215
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 15
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
temperature = 210

[filament:Polymaker PC-Max]
bed_temperature = 120
bridge_fan_speed = 30
compatible_printers = 
cooling = 0
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #3A80CA
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 13
filament_notes = "List of materials tested with standart ABS print settings for MK2:\n\nEsun ABS\nFil-A-Gehr ABS\nHatchboxABS\nPlasty Mladeč ABS"
filament_settings_id = 
filament_soluble = 0
filament_type = ABS
first_layer_bed_temperature = 120
first_layer_temperature = 270
max_fan_speed = 30
min_fan_speed = 10
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
temperature = 270

[filament:Primavalue PVA]
bed_temperature = 60
bridge_fan_speed = 100
compatible_printers = 
cooling = 0
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 100
filament_colour = #FFFFD7
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = "List of materials tested with standart PVA print settings for MK2:\n\nPrimaSelect PVA+\nICE FILAMENTS PVA 'NAUGHTY NATURAL'\nVerbatim BVOH"
filament_settings_id = 
filament_soluble = 1
filament_type = PVA
first_layer_bed_temperature = 60
first_layer_temperature = 195
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 15
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}10{endif}; Filament gcode"
temperature = 195

[filament:Prusa ABS 1.75mm]
bed_temperature = 100
bridge_fan_speed = 30
compatible_printers = 
cooling = 0
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #3A80CA
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 13
filament_notes = "List of materials tested with standart ABS print settings for MK2:\n\nEsun ABS\nFil-A-Gehr ABS\nHatchboxABS\nPlasty Mladeč ABS"
filament_settings_id = 
filament_soluble = 0
filament_type = ABS
first_layer_bed_temperature = 100
first_layer_temperature = 255
max_fan_speed = 30
min_fan_speed = 10
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
temperature = 255

[filament:Prusa HIPS 1.75mm]
bed_temperature = 100
bridge_fan_speed = 50
compatible_printers = 
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 0.9
fan_always_on = 1
fan_below_layer_time = 10
filament_colour = #FFFFD7
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 13
filament_notes = ""
filament_settings_id = 
filament_soluble = 1
filament_type = HIPS
first_layer_bed_temperature = 100
first_layer_temperature = 220
max_fan_speed = 20
min_fan_speed = 20
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}10{endif}; Filament gcode"
temperature = 220

[filament:Prusa PET 1.75mm]
bed_temperature = 90
bridge_fan_speed = 50
compatible_printers = 
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 20
filament_colour = #FF8000
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = "List of manufacturers tested with standart PET print settings for MK2:\n\nE3D Edge\nFillamentum CPE GH100\nPlasty Mladeč PETG"
filament_settings_id = 
filament_soluble = 0
filament_type = PET
first_layer_bed_temperature = 85
first_layer_temperature = 230
max_fan_speed = 50
min_fan_speed = 30
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}45{endif}; Filament gcode"
temperature = 240

[filament:Prusa PLA 1.75mm]
bed_temperature = 60
bridge_fan_speed = 100
compatible_printers = 
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #FF3232
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 15
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nDas Filament\nEsun PLA\nEUMAKERS PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nVerbatim PLA\nVerbatim BVOH"
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 60
first_layer_temperature = 215
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 15
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
temperature = 210

[filament:SemiFlex or Flexfill 98A]
bed_temperature = 50
bridge_fan_speed = 100
compatible_printers = "Original Prusa i3 MK2";"Original Prusa i3 MK2 0.6 nozzle";"Original Prusa i3 MK2 MM Single Mode";"Original Prusa i3 MK2 MM Single Mode 0.6 nozzle";"Original Prusa i3 MK3"
cooling = 0
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1.2
fan_always_on = 0
fan_below_layer_time = 100
filament_colour = #00CA0A
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 2.5
filament_notes = "List of materials tested with FLEX print settings & FLEX material settings for MK2:\n\nFillamentum Flex 98A\nFillamentum Flex 92A\nPlasty Mladeč PP\nPlasty Mladeč TPE32 \nPlasty Mladeč TPE88"
filament_settings_id = 
filament_soluble = 0
filament_type = FLEX
first_layer_bed_temperature = 50
first_layer_temperature = 220
max_fan_speed = 90
min_fan_speed = 70
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}10{endif}; Filament gcode"
temperature = 230

[filament:Taulman Bridge 1.75mm]
bed_temperature = 50
bridge_fan_speed = 40
compatible_printers = 
cooling = 0
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #DEE0E6
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 90
first_layer_temperature = 240
max_fan_speed = 5
min_fan_speed = 0
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}10{endif}; Filament gcode"
temperature = 250

[filament:Taulman T-Glase 1.75mm]
bed_temperature = 90
bridge_fan_speed = 40
compatible_printers = 
cooling = 0
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 20
filament_colour = #FF8000
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = ""
filament_settings_id = 
filament_soluble = 0
filament_type = PET
first_layer_bed_temperature = 90
first_layer_temperature = 240
max_fan_speed = 5
min_fan_speed = 0
min_print_speed = 5
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}30{endif}; Filament gcode"
temperature = 240

[filament:Verbatim BVOH]
bed_temperature = 60
bridge_fan_speed = 100
compatible_printers = 
cooling = 0
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 0
fan_below_layer_time = 100
filament_colour = #FFFFD7
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nDas Filament\nEsun PLA\nEUMAKERS PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nVerbatim PLA\nVerbatim BVOH"
filament_settings_id = 
filament_soluble = 1
filament_type = PLA
first_layer_bed_temperature = 60
first_layer_temperature = 215
max_fan_speed = 100
min_fan_speed = 85
min_print_speed = 15
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}10{endif}; Filament gcode"
temperature = 210

[filament:Verbatim PP]
bed_temperature = 100
bridge_fan_speed = 100
compatible_printers = 
cooling = 1
disable_fan_first_layers = 2
end_filament_gcode = "; Filament-specific end gcode"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #DEE0E6
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 5
filament_notes = "List of materials tested with standart PLA print settings for MK2:\n\nEsun PLA\nFiberlogy HD-PLA\nFillamentum PLA\nFloreon3D\nHatchbox PLA\nPlasty Mladeč PLA\nPrimavalue PLA\nProto pasta Matte Fiber\nEUMAKERS PLA"
filament_settings_id = 
filament_soluble = 0
filament_type = PLA
first_layer_bed_temperature = 100
first_layer_temperature = 220
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 15
slowdown_below_layer_time = 10
start_filament_gcode = "M900 K{if printer_preset==\"Original Prusa i3 MK2 MultiMaterial\"}200{elsif printer_preset==\"Original Prusa i3 MK2 MM Single Mode\"}200{else}10{endif}; Filament gcode"
temperature = 220

[printer:Original Prusa i3 MK2]
bed_shape = 0x0,250x0,250x210,0x210
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\n\n
between_objects_gcode = 
deretract_speed = 0
end_gcode = G4 ; wait\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nG1 X0 Y200; home X axis\nM84 ; disable motors
extruder_colour = #FFFF00
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
max_layer_height = 0.25
min_layer_height = 0.07
nozzle_diameter = 0.4
octoprint_apikey = 
octoprint_host = 
printer_notes = 
printer_settings_id = 
retract_before_travel = 1
retract_before_wipe = 0%
retract_layer_change = 1
retract_length = 0.8
retract_length_toolchange = 3
retract_lift = 0.5
retract_lift_above = 1
retract_lift_below = 199
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 35
serial_port = 
serial_speed = 250000
single_extruder_multi_material = 0
start_gcode = M115 U3.1.0 ; tell printer latest fw version\nM83  ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG1 Y-3.0 F1000.0 ; go outside print area\nG92 E0.0\nG1 X60.0 E9.0  F1000.0 ; intro line\nG1 X100.0 E12.5  F1000.0 ; intro line\nG92 E0.0
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 1
wipe = 1
z_offset = 0

[printer:Original Prusa i3 MK2 0.25 nozzle]
bed_shape = 0x0,250x0,250x210,0x210
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\n\n
between_objects_gcode = 
deretract_speed = 0
end_gcode = G4 ; wait\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nG1 X0 Y200; home X axis\nM84 ; disable motors
extruder_colour = #FFFF00
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
max_layer_height = 0.1
min_layer_height = 0.05
nozzle_diameter = 0.25
octoprint_apikey = 
octoprint_host = 
printer_notes = 
printer_settings_id = 
retract_before_travel = 1
retract_before_wipe = 0%
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 3
retract_lift = 0.5
retract_lift_above = 1
retract_lift_below = 199
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 50
serial_port = 
serial_speed = 250000
single_extruder_multi_material = 0
start_gcode = M115 U3.1.0 ; tell printer latest fw version\nM83  ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG1 Y-3.0 F1000.0 ; go outside print area\nG92 E0.0\nG1 X60.0 E9.0  F1000.0 ; intro line\nG1 X100.0 E12.5  F1000.0 ; intro line\nG92 E0.0
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 0
wipe = 1
z_offset = 0

[printer:Original Prusa i3 MK2 0.6 nozzle]
bed_shape = 0x0,250x0,250x210,0x210
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\n\n
between_objects_gcode = 
deretract_speed = 0
end_gcode = G4 ; wait\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nG1 X0 Y200; home X axis\nM84 ; disable motors
extruder_colour = #FFFF00
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
max_layer_height = 0.35
min_layer_height = 0.1
nozzle_diameter = 0.6
octoprint_apikey = 
octoprint_host = 
printer_notes = 
printer_settings_id = 
retract_before_travel = 1
retract_before_wipe = 0%
retract_layer_change = 1
retract_length = 0.8
retract_length_toolchange = 3
retract_lift = 0.5
retract_lift_above = 1
retract_lift_below = 199
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 35
serial_port = 
serial_speed = 250000
single_extruder_multi_material = 0
start_gcode = M115 U3.1.0 ; tell printer latest fw version\nM83  ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG1 Y-3.0 F1000.0 ; go outside print area\nG92 E0.0\nG1 X60.0 E9.0  F1000.0 ; intro line\nG1 X100.0 E12.5  F1000.0 ; intro line\nG92 E0.0
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 1
wipe = 1
z_offset = 0

[printer:Original Prusa i3 MK2 MM Single Mode]
bed_shape = 0x0,250x0,250x210,0x210
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\n\n
between_objects_gcode = 
deretract_speed = 50
end_gcode = G1 E-4 F2100.00000\nG91\nG1 Z1 F7200.000\nG90\nG1 X245 Y1\nG1 X240 E4\nG1 F4000\nG1 X190 E2.7  \nG1 F4600\nG1 X110 E2.8\nG1 F5200\nG1 X40 E3  \nG1 E-15.0000 F5000\nG1 E-50.0000 F5400\nG1 E-15.0000 F3000\nG1 E-12.0000 F2000\nG1 F1600\nG1 X0 Y1 E3.0000\nG1 X50 Y1 E-5.0000\nG1 F2000\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-5.0000\nG1 F2400\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-5.0000\nG1 F2400\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-3.0000\nG4 S0\nM107 ; fan off\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nG28 X0  ; home X axis\nM84     ; disable motors\n\n
extruder_colour = #FFAA55
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
max_layer_height = 0.25
min_layer_height = 0.07
nozzle_diameter = 0.4
octoprint_apikey = 
octoprint_host = 
printer_notes = 
printer_settings_id = 
retract_before_travel = 3
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 4
retract_length_toolchange = 6
retract_lift = 0.5
retract_lift_above = 0
retract_lift_below = 199
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 80
serial_port = 
serial_speed = 250000
single_extruder_multi_material = 1
start_gcode = M115 U3.1.0 ; tell printer latest fw version\n; Start G-Code sequence START\nT?\nM104 S[first_layer_temperature]\nM140 S[first_layer_bed_temperature]\nM109 S[first_layer_temperature]\nM190 S[first_layer_bed_temperature]\nG21 ; set units to millimeters\nG90 ; use absolute coordinates\nM83 ; use relative distances for extrusion\nG28 W\nG80\nG92 E0.0\nM203 E100\nM92 E140\nG1 Z0.250 F7200.000\nG1 X50.0 E80.0  F1000.0\nG1 X160.0 E20.0  F1000.0\nG1 Z0.200 F7200.000\nG1 X220.0 E13 F1000.0\nG1 X240.0 E0 F1000.0\nG1 E-4 F1000.0\nG92 E0.0
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 1
wipe = 1
z_offset = 0

[printer:Original Prusa i3 MK2 MM Single Mode 0.6 nozzle]
bed_shape = 0x0,250x0,250x210,0x210
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\n\n
between_objects_gcode = 
deretract_speed = 50
end_gcode = G1 E-4 F2100.00000\nG91\nG1 Z1 F7200.000\nG90\nG1 X245 Y1\nG1 X240 E4\nG1 F4000\nG1 X190 E2.7  \nG1 F4600\nG1 X110 E2.8\nG1 F5200\nG1 X40 E3  \nG1 E-15.0000 F5000\nG1 E-50.0000 F5400\nG1 E-15.0000 F3000\nG1 E-12.0000 F2000\nG1 F1600\nG1 X0 Y1 E3.0000\nG1 X50 Y1 E-5.0000\nG1 F2000\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-5.0000\nG1 F2400\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-5.0000\nG1 F2400\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-3.0000\nG4 S0\nM107 ; fan off\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nG28 X0  ; home X axis\nM84     ; disable motors\n\n
extruder_colour = #FFAA55
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
max_layer_height = 0.25
min_layer_height = 0.07
nozzle_diameter = 0.6
octoprint_apikey = 
octoprint_host = 
printer_notes = 
printer_settings_id = 
retract_before_travel = 3
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 4
retract_length_toolchange = 6
retract_lift = 0.5
retract_lift_above = 0
retract_lift_below = 199
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 80
serial_port = 
serial_speed = 250000
single_extruder_multi_material = 1
start_gcode = M115 U3.1.0 ; tell printer latest fw version\n; Start G-Code sequence START\nT?\nM104 S[first_layer_temperature]\nM140 S[first_layer_bed_temperature]\nM109 S[first_layer_temperature]\nM190 S[first_layer_bed_temperature]\nG21 ; set units to millimeters\nG90 ; use absolute coordinates\nM83 ; use relative distances for extrusion\nG28 W\nG80\nG92 E0.0\nM203 E100\nM92 E140\nG1 Z0.250 F7200.000\nG1 X50.0 E80.0  F1000.0\nG1 X160.0 E20.0  F1000.0\nG1 Z0.200 F7200.000\nG1 X220.0 E13 F1000.0\nG1 X240.0 E0 F1000.0\nG1 E-4 F1000.0\nG92 E0.0
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 1
wipe = 1
z_offset = 0

[printer:Original Prusa i3 MK2 MultiMaterial]
bed_shape = 0x0,250x0,250x210,0x210
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\n\n
between_objects_gcode = 
deretract_speed = 50,50,50,50
end_gcode = {if not has_wipe_tower}\n; Pull the filament into the cooling tubes.\nG1 E-4 F2100.00000\nG91\nG1 Z1 F7200.000\nG90\nG1 X245 Y1\nG1 X240 E4\nG1 F4000\nG1 X190 E2.7  \nG1 F4600\nG1 X110 E2.8\nG1 F5200\nG1 X40 E3  \nG1 E-15.0000 F5000\nG1 E-50.0000 F5400\nG1 E-15.0000 F3000\nG1 E-12.0000 F2000\nG1 F1600\nG1 X0 Y1 E3.0000\nG1 X50 Y1 E-5.0000\nG1 F2000\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-5.0000\nG1 F2400\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-5.0000\nG1 F2400\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-3.0000\nG4 S0\n{endif}\nM107 ; fan off\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nG28 X0  ; home X axis\nM84     ; disable motors
extruder_colour = #FFAA55;#5182DB;#4ECDD3;#FB7259
extruder_offset = 0x0,0x0,0x0,0x0
gcode_flavor = reprap
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
max_layer_height = 0.25,0.25,0.25,0.25
min_layer_height = 0.07,0.07,0.07,0.07
nozzle_diameter = 0.4,0.4,0.4,0.4
octoprint_apikey = 
octoprint_host = 
printer_notes = 
printer_settings_id = 
retract_before_travel = 3,3,3,3
retract_before_wipe = 60%,60%,60%,60%
retract_layer_change = 0,0,0,0
retract_length = 4,4,4,4
retract_length_toolchange = 4,4,4,4
retract_lift = 0.5,0.5,0.5,0.5
retract_lift_above = 0,0,0,0
retract_lift_below = 199,199,199,199
retract_restart_extra = 0,0,0,0
retract_restart_extra_toolchange = 0,0,0,0
retract_speed = 80,80,80,80
serial_port = 
serial_speed = 250000
single_extruder_multi_material = 1
start_gcode = M115 U3.1.0 ; tell printer latest fw version\n; Start G-Code sequence START\nT[initial_tool]\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG21 ; set units to millimeters\nG90 ; use absolute coordinates\nM83 ; use relative distances for extrusion\nG28 W\nG80\nG92 E0.0\nM203 E100 ; set max feedrate\nM92 E140 ; E-steps per filament milimeter\n{if not has_wipe_tower}\nG1 Z0.250 F7200.000\nG1 X50.0 E80.0  F1000.0\nG1 X160.0 E20.0  F1000.0\nG1 Z0.200 F7200.000\nG1 X220.0 E13 F1000.0\nG1 X240.0 E0 F1000.0\nG1 E-4 F1000.0\n{endif}\nG92 E0.0
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 0
wipe = 1,1,1,1
z_offset = 0

[printer:Original Prusa i3 MK2 MultiMaterial 0.6 nozzle]
bed_shape = 0x0,250x0,250x210,0x210
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\n\n
between_objects_gcode = 
deretract_speed = 50,50,50,50
end_gcode = {if not has_wipe_tower}\nG1 E-4 F2100.00000\nG91\nG1 Z1 F7200.000\nG90\nG1 X245 Y1\nG1 X240 E4\nG1 F4000\nG1 X190 E2.7  \nG1 F4600\nG1 X110 E2.8\nG1 F5200\nG1 X40 E3  \nG1 E-15.0000 F5000\nG1 E-50.0000 F5400\nG1 E-15.0000 F3000\nG1 E-12.0000 F2000\nG1 F1600\nG1 X0 Y1 E3.0000\nG1 X50 Y1 E-5.0000\nG1 F2000\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-5.0000\nG1 F2400\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-5.0000\nG1 F2400\nG1 X0 Y1 E5.0000\nG1 X50 Y1 E-3.0000\nG4 S0\n{endif}\nM107 ; fan off\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nG28 X0  ; home X axis\nM84     ; disable motors\n
extruder_colour = #FFAA55;#5182DB;#4ECDD3;#FB7259
extruder_offset = 0x0,0x0,0x0,0x0
gcode_flavor = reprap
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
max_layer_height = 0.25,0.25,0.25,0.25
min_layer_height = 0.07,0.07,0.07,0.07
nozzle_diameter = 0.6,0.6,0.6,0.6
octoprint_apikey = 
octoprint_host = 
printer_notes = 
printer_settings_id = 
retract_before_travel = 3,3,3,3
retract_before_wipe = 60%,60%,60%,60%
retract_layer_change = 0,0,0,0
retract_length = 4,4,4,4
retract_length_toolchange = 4,4,4,4
retract_lift = 0.5,0.5,0.5,0.5
retract_lift_above = 0,0,0,0
retract_lift_below = 199,199,199,199
retract_restart_extra = 0,0,0,0
retract_restart_extra_toolchange = 0,0,0,0
retract_speed = 80,80,80,80
serial_port = 
serial_speed = 250000
single_extruder_multi_material = 1
start_gcode = M115 U3.1.0 ; tell printer latest fw version\n; Start G-Code sequence START\nT[initial_tool]\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG21 ; set units to millimeters\nG90 ; use absolute coordinates\nM83 ; use relative distances for extrusion\nG28 W\nG80\nG92 E0.0\nM203 E100\nM92 E140\n{if not has_wipe_tower}\nG1 Z0.250 F7200.000\nG1 X50.0 E80.0  F1000.0\nG1 X160.0 E20.0  F1000.0\nG1 Z0.200 F7200.000\nG1 X220.0 E13 F1000.0\nG1 X240.0 E0 F1000.0\nG1 E-4 F1000.0\n{endif}\nG92 E0.0
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 0
wipe = 1,1,1,1
z_offset = 0

[printer:Original Prusa i3 MK3]
bed_shape = 0x0,250x0,250x210,0x210
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\n\n
between_objects_gcode = 
deretract_speed = 0
end_gcode = G4 ; wait\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nG1 X0 Y200; home X axis\nM84 ; disable motors
extruder_colour = #FFFF00
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
max_layer_height = 0.25
min_layer_height = 0.07
nozzle_diameter = 0.4
octoprint_apikey = 
octoprint_host = 
printer_notes = 
retract_before_travel = 1
retract_before_wipe = 0%
retract_layer_change = 1
retract_length = 0.8
retract_length_toolchange = 3
retract_lift = 0.5
retract_lift_above = 1
retract_lift_below = 199
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 35
serial_port = 
serial_speed = 250000
single_extruder_multi_material = 0
start_gcode = M115 U3.1.0 ; tell printer latest fw version\nM83  ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\nG1 Y-3.0 F1000.0 ; go outside pritn area\nG1 X60.0 E9.0  F1000.0 ; intro line\nG1 X100.0 E12.5  F1000.0 ; intro line
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 1
wipe = 1
z_offset = 0

[presets]
print = 0.15mm 100mms Linear Advance
printer = Original Prusa i3 MK2
filament = Prusa PLA 1.75mm