{
	"type": "machine",
	"setting_id": "GM001",
	"name": "Anycubic Chiron 0.4 nozzle",
	"from": "system",
	"instantiation": "true",
	"inherits": "fdm_machine_common",
	"printer_model": "Anycubic Chiron",
	"default_print_profile": "0.20mm Standard @Anycubic Chiron",
	"nozzle_diameter": [
		"0.4"
	],
	"printable_area": [
		"0x0",
		"400x0",
		"400x400",
		"0x400"
	],
	"printable_height": "450",
	"nozzle_type": "undefine",
	"auxiliary_fan": "0",
    "machine_max_acceleration_e": [
        "5000",
        "5000"
    ],
	"machine_max_acceleration_extruding": [
		"1250",
		"1250"
	],
	"machine_max_acceleration_retracting": [
		"1250",
		"1250"
	],
	"machine_max_acceleration_travel": [
		"1500",
		"1250"
	],
	"machine_max_acceleration_x": [
		"1000",
		"960"
	],
	"machine_max_acceleration_y": [
		"1000",
		"960"
	],
	"machine_max_acceleration_z": [
		"200",
		"200"
	],
	"machine_max_speed_e": [
		"120",
		"120"
	],
	"machine_max_speed_x": [
		"300",
		"100"
	],
	"machine_max_speed_y": [
		"300",
		"100"
	],
	"machine_max_speed_z": [
		"12",
		"12"
	],
	"machine_max_jerk_e": [
		"4.5",
		"4.5"
	],
	"machine_max_jerk_x": [
		"8",
		"8"
	],
	"machine_max_jerk_y": [
		"8",
		"8"
	],
	"machine_max_jerk_z": [
		"0.4",
		"0.4"
	],
	"max_layer_height": [
		"0.3"
	],
	"min_layer_height": [
		"0.1"
	],
	"printer_settings_id": "Anycubic",
	"retraction_minimum_travel": [
		"1"
	],
	"retract_before_wipe": [
		"0%"
	],
	"retraction_length": [
		"2"
	],
	"retract_length_toolchange": [
		"4"
	],
	"retraction_speed": [
		"40"
	],
	"deretraction_speed": [
		"0"
	],
	"single_extruder_multi_material": "0",
	"change_filament_gcode": "M600",
	"machine_pause_gcode": "M601",
	"default_filament_profile": [
		"Anycubic Generic PLA"
	],
	"machine_start_gcode": "M104 S140;start the nozzle preheat and don't wait\nG21;metric values\nG90;absolute positioning\nM82;set extruder to absolute mode\nM107       ;start with the fan off\nG28;home all\nM190 S[bed_temperature_initial_layer_single]; set wait for bed temp\nM109 S[nozzle_temperature_initial_layer] ; wait for extruder temp\nG1 Z15.0 F3600 ;move the platform down 15mm\nG92 E0;zero the extruded length\nG1 F200 E40;extrude 40mm of feed stock\nG92 E0;zero the extruded length again\nG1 F3600",
	"machine_end_gcode": "M104 S0;extruder heater off\nM140 S0  ;heated bed heater off (if you have it)\nG91;relative positioning\nG1 E-4 F300;retract the filament a bit before lifting the nozzle, to release some of the pressure\nG1 Z+10 F3600 ;move Z up a bit\nG90;absolute positioning\nG1 X-10 F3000; get the head off the bed\nG1 F3000 Y400;kick the bed out\nM84;steppers off",
	"before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0.0\n;[layer_z]\n\n",
	"layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]",
	"scan_first_layer": "0"
}