{
  "type": "machine",
  "setting_id": "GM001",
  "name": "Elegoo Neptune 4 Pro (0.8 nozzle)",
  "from": "system",
  "instantiation": "true",
  "inherits": "fdm_neptune_4_common",
  "printer_model": "Elegoo Neptune 4 Pro",
  "gcode_flavor": "klipper",
  "default_print_profile": "0.20mm Standard @Elegoo Neptune4Pro (0.8 nozzle)",
  "nozzle_diameter": [
    "0.8"
  ],
  "printer_variant": "0.8",
  "printable_area": [
    "0x0",
    "235x0",
    "235x230",
    "0x230"
  ],
  "printable_height": "265",
  "nozzle_type": "hardened_steel",
  "auxiliary_fan": "0",
  "machine_max_acceleration_e": [
    "5000",
    "5000"
  ],
  "machine_max_acceleration_extruding": [
    "20000",
    "20000"
  ],
  "machine_max_acceleration_retracting": [
    "5000",
    "5000"
  ],
  "machine_max_acceleration_travel": [
    "20000",
    "20000"
  ],
  "machine_max_acceleration_x": [
    "20000",
    "20000"
  ],
  "machine_max_acceleration_y": [
    "20000",
    "20000"
  ],
  "machine_max_acceleration_z": [
    "500",
    "200"
  ],
  "machine_max_speed_e": [
    "25",
    "25"
  ],
  "machine_max_speed_x": [
    "500",
    "200"
  ],
  "machine_max_speed_y": [
    "500",
    "200"
  ],
  "machine_max_speed_z": [
    "12",
    "12"
  ],
  "machine_max_jerk_e": [
    "2.5",
    "2.5"
  ],
  "machine_max_jerk_x": [
    "12",
    "12"
  ],
  "machine_max_jerk_y": [
    "12",
    "12"
  ],
  "machine_max_jerk_z": [
    "0.2",
    "0.4"
  ],
  "max_layer_height": [
    "0.6"
  ],
  "min_layer_height": [
    "0.08"
  ],
  "printer_settings_id": "Elegoo",
  "retraction_minimum_travel": [
    "1"
  ],
  "retract_before_wipe": [
    "85%"
  ],
  "retraction_length": [
    "0.8"
  ],
  "retraction_speed": [
    "60"
  ],
  "retract_length_toolchange": [
    "2"
  ],
  "deretraction_speed": [
    "45"
  ],
  "single_extruder_multi_material": "1",
  "change_filament_gcode": "M600",
  "machine_pause_gcode": "PAUSE",
  "default_filament_profile": [
    "Elegoo Generic PLA @0.8 nozzle"
  ],
  "machine_start_gcode": ";ELEGOO NEPTUNE 4 PRO\nM220 S100 ;Set the feed speed to 100%\nM221 S100 ;Set the flow rate to 100%\nM104 S140\nM190 S[bed_temperature_initial_layer_single]\nG90\nG28 ;home\nG1 Z10 F300\nG1 X67.5 Y0 F6000\nG1 Z0 F300\nM109 S[nozzle_temperature_initial_layer]\nG92 E0 ;Reset Extruder\nG1 X67.5 Y0 Z0.4 F300 ;Move to start position\nG1 X167.5 E30 F400 ;Draw the first line\nG1 Z0.6 F120.0 ;Move to side a little\nG1 X162.5 F3000\nG92 E0 ;Reset Extruder",
  "machine_end_gcode": ";PRINT END\nG91 ;Relative positionning\nG1 E-2 F2700 ;Retract a bit\nG1 E-8 X5 Y5 Z3 F3000 ;Retract\nG90 ;Absolute positionning\nG1 X10 Y220 F6000;Finish print\nM106 S0 ;Turn-off fan\nM104 S0 ;Turn-off hotend\nM140 S0 ;Turn-off bed\nM84 X Y E ;Disable all steppers but Z",
  "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n",
  "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]",
  "scan_first_layer": "0"
}