{
  "type": "machine",
  "setting_id": "GM003",
  "name": "Kingroon KLP1 0.4 nozzle",
  "from": "system",
  "instantiation": "true",
  "inherits": "fdm_klipper_common",
  "printer_model": "Kingroon KLP1",
  "default_filament_profile": "Kingroon Generic PLA",
  "default_print_profile": "0.20mm Standard @Kingroon KLP1",

  "thumbnails": [ "100x100" ],
  "change_filament_gcode": "",
  "deretraction_speed": [ "90" ],
  "enable_filament_ramming": "1",
  "extra_loading_move": "-2",
  "extruder_clearance_height_to_rod": "36",
  "extruder_clearance_radius": "65",
  "high_current_on_filament_swap": "0",
  "machine_unload_filament_time": "0",
  "min_layer_height": "0.08",
  "parking_pos_retraction": "92",
  "purge_in_prime_tower": "1",
  "retract_lift_above": [ "0" ],
  "retract_lift_below": [ "0" ],
  "retract_lift_enforce": ["All Surfaces"],
  "bed_exclude_area": ["0x0"],
  "extruder_colour": ["#FCE94F"],
  "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]",
  "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\n;[layer_z]\nG92 E0\n",
  "machine_end_gcode": "G91; relative positioning\n G1 Z1.0 F3000 ; move z up little to prevent scratching of print\n G90; absolute positioning\n G1 X0 Y200 F1000 ; prepare for part removal\n M104 S0; turn off extruder\n M140 S0 ; turn off bed\n G1 X0 Y200 F1000 ; prepare for part removal\n M84 ; disable motors\n M106 S0 ; turn off fan",
  "machine_max_acceleration_e": ["5000", "5000"],
  "machine_max_acceleration_extruding": ["5000", "20000"],
  "machine_max_acceleration_retracting": ["5000", "5000"],
  "machine_max_acceleration_travel": ["9000", "9000"],
  "machine_max_acceleration_x": ["10000", "20000"],
  "machine_max_acceleration_y": ["10000", "20000"],
  "machine_max_acceleration_z": ["500", "200"],
  "machine_max_jerk_e": ["2.5", "2.5"],
  "machine_max_jerk_x": ["20", "9"],
  "machine_max_jerk_y": ["20", "9"],
  "machine_max_jerk_z": ["0.2", "0.4"],
  "machine_max_speed_e": ["100", "25"],
  "machine_max_speed_z": ["50", "12"],
  "machine_pause_gcode": "PAUSE",
  "machine_start_gcode": "M190 S[bed_temperature_initial_layer_single]\nM109 S[nozzle_temperature_initial_layer]\nG28 ; h1ome all axes\n M117 ;Purge extruder\n G92 E0 ; reset extruder\n G1 Z1.0 F3000 ; move z up little to prevent scratching of surface\n G1 X2 Y20 Z0.3 F5000.0 ; move to start-line position\n G1 X2 Y175.0 Z0.3 F1500.0 E15 ; draw 1st line\n G1 X2 Y175.0 Z0.4 F5000.0 ; move to side a little\n G1 X2 Y20 Z0.4 F1500.0 E30 ; draw 2nd line\n G92 E0 ; reset extruder\n G1 Z1.0 F3000 ; move z up little to prevent scratching of surface",
  "max_layer_height": ["0.32"],
  "retraction_length": ["1"],
  "retraction_speed": ["90"],
  "use_firmware_retraction": "0",
  "wipe": ["1"],
  "z_hop": ["0"],
  "printable_area": [
    "0x0",
    "230x0",
    "230x230",
    "0x230"
],
"printable_height": "210",
"nozzle_diameter": ["0.4"]
}