{
  "type": "machine",
  "setting_id": "GM003",
  "name": "Kingroon KP3S V1 0.4 nozzle",
  "from": "system",
  "instantiation": "true",
  "inherits": "fdm_klipper_common",
  "printer_model": "Kingroon KP3S V1",
  "default_filament_profile": "Kingroon Generic PLA",
  "default_print_profile": "0.20mm Standard @Kingroon KP3S V1",

  "thumbnails": [ "100x100" ],
  "change_filament_gcode": "",
  "best_object_pos": "0.5,0.5",
  "change_extrusion_role_gcode": "",
  "cooling_tube_length": "0",
  "cooling_tube_retraction": "0",
  "deretraction_speed": [ "30" ],
  "disable_m73": "0",
  "emit_machine_limits_to_gcode": "1",
  "enable_filament_ramming": "0",
  "head_wrap_detect_zone": [],
  "enable_long_retraction_when_cut": "0",
  "long_retractions_when_cut": [
    "0"
  ],
  "retract_before_wipe": [ "0%" ],
  "retraction_distances_when_cut": [
    "18"
  ],
  "extra_loading_move": "0",
  "extruder_clearance_height_to_rod": "36",
  "extruder_clearance_radius": "65",
  "high_current_on_filament_swap": "0",
  "machine_unload_filament_time": "0",
  "min_layer_height": "0.08",
  "parking_pos_retraction": "0",
  "preferred_orientation": "0",
  "printing_by_object_gcode": "",
  "purge_in_prime_tower": "0",
  "retract_lift_above": [ "0" ],
  "retract_lift_below": [ "0" ],
  "retract_lift_enforce": ["All Surfaces"],
  "bed_exclude_area": ["0x0"],
  "extruder_colour": ["#FCE94F"],
  "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]",
  "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\n;[layer_z]\nG92 E0\n",
  "machine_end_gcode": "G91; relative positioning\n G1 Z1.0 F3000 ; move z up little to prevent scratching of print\n G90; absolute positioning\n G1 X0 Y180 F1000 ; prepare for part removal\n M104 S0; turn off extruder\n M140 S0 ; turn off bed\n G1 X0 Y180 F1000 ; prepare for part removal\n M84 ; disable motors\n M106 S0 ; turn off fan",
  "machine_max_acceleration_e": ["5000", "5000"],
  "machine_max_acceleration_extruding": ["10000", "20000"],
  "machine_max_acceleration_retracting": ["5000", "5000"],
  "machine_max_acceleration_travel": ["20000", "20000"],
  "machine_max_acceleration_x": ["10000", "20000"],
  "machine_max_acceleration_y": ["10000", "20000"],
  "machine_max_acceleration_z": ["500", "200"],
  "machine_max_jerk_e": ["2.5", "2.5"],
  "machine_max_jerk_x": ["9", "9"],
  "machine_max_jerk_y": ["9", "9"],
  "machine_max_jerk_z": ["0.2", "0.4"],
  "machine_max_speed_e": ["100", "25"],
  "machine_max_speed_z": ["12", "12"],
  "machine_pause_gcode": "PAUSE",
  "machine_start_gcode": "M104 S{first_layer_temperature[0]} ; set final nozzle temp\nM190 S[bed_temperature_initial_layer_single]\nM109 S[nozzle_temperature_initial_layer]\nM83\nG28 ; h1ome all axes\nG1 Z0.2                                   ; lift nozzle a bit \nG92 E0 \nG1 Y-3 F2400   \nG1 X50 F2400                                  ; zero the extruded length \nG1 X115  E40 F500                       ; Extrude 25mm of filament in a 5cm line. \nG92 E0                                     ; zero the extruded length again \nG1 E-0.2 F3000                                ; Retract a little \nG1 X180 F4000                              ; Quickly wipe away from the filament line\nM117",
  "manual_filament_change": "0",
  "nozzle_height": "4",
  "nozzle_type": "brass",
  "max_layer_height": ["0.32"],
  "retraction_length": ["0.8"],
  "retraction_speed": ["30"],
  "support_air_filtration": "1",
  "support_chamber_temp_control": "1",
  "support_multi_bed_types": "0",
  "use_firmware_retraction": "0",
  "wipe": ["1"],
  "z_hop": ["0"],
  "z_offset": "0",
  "printable_area": [
    "0x0",
    "180x0",
    "180x180",
    "0x180"
],
"printable_height": "180",
"nozzle_diameter": ["0.4"]
}