{
    "type": "machine",
    "setting_id": "GM003",
    "name": "Artillery Sidewinder X2 0.4 nozzle",
    "from": "system",
    "instantiation": "true",
    "inherits": "fdm_machine_common",
    "printer_model": "Artillery Sidewinder X2",
    "default_print_profile": "0.20mm Standard @Artillery X2",
    "nozzle_diameter": [
        "0.4"
    ],
    "bed_exclude_area": [
      "0x0"
    ],
    "printable_area": [
      "0x0",
      "300x0",
      "300x300",
      "0x300"
    ],
    "printable_height": "400",
	"nozzle_type": "hardened_steel",
	"auxiliary_fan": "0",
	"machine_max_acceleration_extruding": [
		"1250",
		"1250"
	],
	"machine_max_acceleration_retracting": [
		"1250",
		"1250"
	],
	"machine_max_acceleration_travel": [
		"1000",
		"1000"
	],
	"machine_max_acceleration_x": [
		"1000",
		"960"
	],
	"machine_max_acceleration_y": [
		"1000",
		"960"
	],
	"machine_max_acceleration_z": [
		"1000",
		"1000"
	],
	"machine_max_speed_e": [
		"120",
		"120"
	],
	"machine_max_speed_x": [
		"200",
		"100"
	],
	"machine_max_speed_y": [
		"200",
		"100"
	],
	"machine_max_speed_z": [
		"12",
		"12"
	],
	"machine_max_jerk_e": [
		"1.5",
		"1.5"
	],
	"machine_max_jerk_x": [
		"8",
		"8"
	],
	"machine_max_jerk_y": [
		"8",
		"8"
	],
	"machine_max_jerk_z": [
		"0.4",
		"0.4"
	],
	"max_layer_height": [
		"0.25"
	],
	"min_layer_height": [
		"0.07"
	],
	"printer_settings_id": "Artillery",
	"retraction_minimum_travel": [
		"1"
	],
	"retract_before_wipe": [
		"0%"
	],
	"retraction_length": [
		"0.8"
	],
	"retract_length_toolchange": [
		"4"
	],
	"retraction_speed": [
        "35"
    ],
	"deretraction_speed": [
		"0"
	],
	"single_extruder_multi_material": "1",
	"change_filament_gcode": "",
	"machine_pause_gcode": "M0",
	"default_filament_profile": [
		"Artillery Generic PLA"
	],
    "machine_start_gcode": "; Initial setups\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM900 K0.12 ; K factor\nM900 W[line_width] H[layer_height] D[filament_diameter]\nM200 D0 ; disable volumetric e\nM220 S100 ; reset speed factor to 100%\nM221 S100 ; reset extrusion rate to 100%\n\n; Set the heating\nM190 S[bed_temperature_initial_layer_single] ; wait for bed to heat up\nM104 S[nozzle_temperature_initial_layer] ; start nozzle heating but don't wait\n\n; Home\nG1 Z3 F3000 ; move z up little to prevent scratching of surface\nG28 ; home all axes\nG1 X3 Y3 F5000 ; move to corner of the bed to avoid ooze over centre\n\n; Wait for final heating\nM109 S[nozzle_temperature_initial_layer] ; wait for the nozzle to heat up\nM190 S[bed_temperature_initial_layer_single] ; wait for the bed to heat up\n\n;Auto bed Leveling\n@BEDLEVELVISUALIZER\nG29 ; ABL T\nM420 S1 Z3 ; reload and fade mesh bed leveling until it reach 3mm Z\n\n; Return to prime position, Prime line routine\nG92 E0 ; Reset Extruder\nG1 Z3 F3000 ; move z up little to prevent scratching of surface\nG1 X10 Y.5 Z0.25 F5000.0 ; Move to start position\nG1 X100 Y.5 Z0.25 F1500.0 E15 ; Draw the first line\nG1 X100 Y.2 Z0.25 F5000.0 ; Move to side a little\nG1 X10 Y.2 Z0.25 F1500.0 E30 ; Draw the second line\nG92 E0 ; Reset Extruder\nM221 S{if layer_height<0.075}100{else}95{endif}",
    "machine_end_gcode": "G4 ; wait\nG92 E0 ; prepare to retract\nG1 E-0.5 F3000; retract to avoid stringing\n\n; Anti-stringing end wiggle\nG91 ; use relative coordinates\nG1 X1 Y1 F1200\n\n; Raise nozzle and present bed\n{if layer_z < printable_height}G1 Z{z_offset+min(layer_z+120, printable_height)}{endif} ; Move print head up\nG90 ; use absolute coordinates\n\n; Reset print setting overrides\nM200 D0 ; disable volumetric e\nM220 S100 ; reset speed factor to 100%\nM221 S100 ; reset extrusion rate to 100%\n\n; Shut down printer\nM106 S0 ; turn-off fan\nM104 S0 ; turn-off hotend\nM140 S0 ; turn-off bed\nM150 P0 ; turn off led\nM85 S0 ; deactivate idle timeout\nM84 ; disable motors\n",
    "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n",
	"layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]",
    "scan_first_layer": "0"
  }