1 extrude move to dustbin
2 max vol of TPU 95A of X1 to 3.6
Signed-off-by: qing.zhang <qing.zhang@bambulab.com>
Change-Id: I0b9d2a1db9c57c58255f95aad8a77772317a3ec9
Start gcode of P1P is wrong.
This is for github issue #1044
Signed-off-by: salt.wei <salt.wei@bambulab.com>
Change-Id: Id078b7c9020ef773373c3486f74dc51385b9dcc0
1. add gcode command for void printing detection
2. fix the issue that the toolhead is not at excess chute position when
smooth timelapse ends, by adding 2s pause after M991 command.
Jira: STUDIO-1996
Change-Id: I40cf16116e742744cea9bd90969e556a9ea2b2f1
(cherry picked from commit 2fbf7ffe6b1bd8850a76e229ff91750c689721b9)
Bambu pa-cf has been modified, generic pa-cf
should be changed as well
Signed-off-by: salt.wei <salt.wei@bambulab.com>
Change-Id: Ie859b41bd4d138a5fab204d6ad6a79806c3f0a9b
1 Use 25% infill density. 60% is too high and useless
2 update filament change gcode
Signed-off-by: salt.wei <salt.wei@bambulab.com>
Change-Id: I9a1fbbfb56b61723aa6e9d6bc44a22f467d92562
Add loop inside sparse infill of lower layer
to provide archor for internal bridge.
This option controls how many lower layers generate
loop path.
Signed-off-by: salt.wei <salt.wei@bambulab.com>
Change-Id: Ifdb6db9090115732aa2cacf5d155b587a10e18fc
(cherry picked from commit 4fdb87ecd5c2e680f6bad2d018ba39cd05f787ce)
Generic PLA silk should use lower filament
volumetroc and retraction
Signed-off-by: salt.wei <salt.wei@bambulab.com>
Change-Id: I8ba11094afc0274710e97d50554001d3a0a4caa1
Jerk handling has been changed in printer.
Changed in slicer as well.
Signed-off-by: salt.wei <salt.wei@bambulab.com>
Change-Id: Ic3aef43a534a7f0b85b734e747dc3ca883faaa46
This is change requirement from printer developer
for github issue #393
Signed-off-by: salt.wei <salt.wei@bambulab.com>
Change-Id: Ief306d89dba70d8515050cbd842edc4e1d22822e
filament_max_volumetric may be 0 which cause zero
flushing speed. Add protection for this issue.
Signed-off-by: salt.wei <salt.wei@bambulab.com>
Change-Id: I866b9d97c9c6d97122a4a2beaf508ce9c72ee3b2
Requirement from user to set filament_start_gcode
and filament_end_gcode. Set these two settings to
advanced mode
Signed-off-by: salt.wei <salt.wei@bambulab.com>
Change-Id: I0d8ddb394b37614d0ef0f10f8434553cb20e9ffd
Make filament_id to be same with information
from nectarine
Signed-off-by: salt.wei <salt.wei@bambulab.com>
Change-Id: I3012d74bb8fe849fbaf9fabab791a6b06335dcf6
Add M400 to avoid temperature switched before flush end.
Signed-off-by: salt.wei <salt.wei@bambulab.com>
Change-Id: I118bb240357e5c820c15e46ae34efa62248fdacc
The extruder offset of X1 and X1C is (0,2).
All generated gcode should minus this value.
Also change the min speed of cooling buffer for
better cooling for small area(from pineapple)
Signed-off-by: salt.wei <salt.wei@bambulab.com>
Change-Id: I06e58a26f8736ae24fa9da02477a9d19114daeca
Filament type of Bambu PA-CF in RFID is PA-CF.
Change it to PA-CF as well in preset to avoid
failure of AMS mapping.
Signed-off-by: salt.wei <salt.wei@bambulab.com>
Change-Id: Ic6b6269123d59863fea2b7d262a124468c95b8af
