* e3v3se: remove jerk settings from processes
Remove jerk settings from Ender3 V3 SE processes to prevent emission of M205 into gcode.
This is due to E3 V3 SE does not use jerk, but has junction deviation
enabled instead. Those two modes are mutually exclusive according to
marlin configuration page:
https://marlinfw.org/docs/configuration/configuration.html#default-acceleration-https://marlinfw.org/docs/configuration/configuration.html#junction-deviation-
Based on M503 output, E3V3SE hase junction deviation enabled:
echo:; Advanced: B<min_segment_time_us> S<min_feedrate> T<min_travel_feedrate> J<junc_dev>
echo: M205 B20000.00 S0.00 T0.00 J0.10
"M205" emitted into gcode is useless since setting jerk settings via
"M205 Xn Yn Zn" does not have any effect on the stock V3 SE firmware.
* e3v3se: update machine retraction settings
Set retraction speed to 40 mm/s as recommended by Creality
Source: https://wiki.creality.com/en/ender-series/ender-3-v3-se/quick-start-guide/user-manual
Set retraction acceleration to 500 mm/s2 to prevent extruder clicking on retraction.
* e3v3se: update start gcode
* Set and wait for bed temperature to stabilize prior to homing.
Bed mesh calibration is done with the bed temp set to 60C.
Performing G28 with bed at room temperature will not compensate
for thermal deformation introduced by heated bed if there are any.
* Remove explicit mesh levelling enable (M420).
Creality FW auto enables M420 once homing (G28) is complete:
"M420 S1 Z10.00"
* e3v3se: disable m73 as not supported in FW
* e3v3se: remove thumbnails
Remove thumbnails generation to not confuse users.
Currently event CrealityPrint does not generate thumbnails for the E3 V3 SE.
* e3v3se: update motion capabilities
Update motion parameters for the Ender 3 V3 SE profiles:
- max acceleration on all axis to 2500 as per product spec
- max X and Y speeds to 250 as per product spec
- max Z speed to 5 as set in factory defaults (M502, M503)
- max E speed to 40 as presented in recommended print parameters on the
product page
Product spec sheet:
https://wiki.creality.com/en/ender-series/ender-3-v3-se/quick-start-guide/user-manual
* Add Ender-3 V3 SE .2, .6, .8 and fix small Ender-3 Pro bug
* Forgot to remove these
* Fix error
* Remove these...
* Why did I delete this?
* Revert deletion
* Add missing profiles
* Create 0.24mm Draft @Creality Ender3V3KE.json
* Apply new nozzle sizes to generic filament
* Maybe this will do it
* Revert 0.4 renames & add to Generic ABS
* Add M420 S1; Enable mesh leveling
* Fix wring nozzle_diameter
* Potentially fix the issue of printer not being added after selected
* Some improvements for supports and machines limits
* Increase z-hop for KE to avoid the nozzle hit the parts
* Changed jerk V3 KE settings to more logical values.
* Decreased jerk
* Speed, acceleration and jerk settings fine-tunings.
* Fixed retraction speed and added missing parameters.
* Fixes for manual filament change
* More tunings and fixes.
* Fixes and tunings
* Formatting
* Decrease z-hop for K1
* Updated thumbnails sizes to the same as Creality Print has.
* Added Creality Ender 3 V3 SE.
* Fixed fine profile.
* Optimized first layer speed (based on Creality Print)
* Brought back Ender-5 (2019)
* Setting Marlin 2 as gcode flavor
* Use inheritance for Ender-3 V3 filament profiles.
* Various improvements.
* Temperature optimisations (less power consumption)
* Fixed some log errors.
* Optimizations
* Reverted support_interface_top_layers
* Added correct jerk and acceleration settings.
* Added retraction speed.
* Re-added missing Ender-5 references in filaments.
* Reverted slow_down_layer_time, Creality print is too optimistic on this at least for Ender 3 V3 SE.
* Optimizations for supports (easier to remove)
---------
Co-authored-by: SoftFever <softfeverever@gmail.com>
