orcaslicer/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Pro (0.8 nozzle).json

{
  "type": "machine",
  "setting_id": "GM001",
  "name": "Elegoo Neptune 4 Pro (0.8 nozzle)",
  "from": "system",
  "instantiation": "true",
  "inherits": "fdm_neptune_4_common",
  "printer_model": "Elegoo Neptune 4 Pro",
  "gcode_flavor": "klipper",
  "default_print_profile": "0.20mm Standard @Elegoo Neptune4Pro (0.8 nozzle)",
  "nozzle_diameter": ["0.8"],
  "printer_variant": "0.8",
  "printable_area": ["0x0", "225x0", "225x225", "0x225"],
  "printable_height": "265",
  "nozzle_type": "hardened_steel",
  "auxiliary_fan": "0",
  "machine_max_acceleration_e": ["5000", "5000"],
  "machine_max_acceleration_extruding": ["20000", "20000"],
  "machine_max_acceleration_retracting": ["5000", "5000"],
  "machine_max_acceleration_travel": ["20000", "20000"],
  "machine_max_acceleration_x": ["20000", "20000"],
  "machine_max_acceleration_y": ["20000", "20000"],
  "machine_max_acceleration_z": ["500", "200"],
  "machine_max_speed_e": ["25", "25"],
  "machine_max_speed_x": ["500", "200"],
  "machine_max_speed_y": ["500", "200"],
  "machine_max_speed_z": ["12", "12"],
  "machine_max_jerk_e": ["2.5", "2.5"],
  "machine_max_jerk_x": ["12", "12"],
  "machine_max_jerk_y": ["12", "12"],
  "machine_max_jerk_z": ["0.2", "0.4"],
  "max_layer_height": ["0.6"],
  "min_layer_height": ["0.08"],
  "printer_settings_id": "Elegoo",
  "retraction_minimum_travel": ["1"],
  "retract_before_wipe": ["85%"],
  "retraction_length": ["0.8"],
  "retraction_speed": ["60"],
  "retract_length_toolchange": ["2"],
  "deretraction_speed": ["45"],
  "single_extruder_multi_material": "1",
  "change_filament_gcode": "PAUSE",
  "machine_pause_gcode": "M0",
  "default_filament_profile": ["Elegoo Generic PLA @0.8 nozzle"],
  "machine_start_gcode": "M413 S0 ; disable Power Loss Recovery\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S120 ; set temporary nozzle temp to prevent oozing during homing and auto bed leveling\nM140 S[bed_temperature_initial_layer_single] ; set final bed temp\nG4 S10 ; allow partial nozzle warmup\nG28 ; home all axis\n;G29 ; run abl mesh\nM420 S1 ; load mesh\nG1 Z50 F240\nG1 X2 Y10 F3000\n\nM190 S[bed_temperature_initial_layer_single] ; wait for bed temp to stabilize\nM109 S[nozzle_temperature_initial_layer] ; wait for nozzle temp to stabilize\nG1 Z0.28 F240\nG92 E0\nG1 Y140 E10 F1500 ; prime the nozzle\nG1 X2.3 F5000\nG92 E0\nG1 Y10 E10 F1200 ; prime the nozzle\nG92 E0",
  "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < printable_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors",
  "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n",
  "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]",
  "scan_first_layer": "0"
}