orcaslicer/resources/profiles/Elegoo/machine/Elegoo Neptune 2D 0.4 nozzle.json

{
    "type": "machine",
    "setting_id": "GM_Elegoo_002",
    "name": "Elegoo Neptune 2D 0.4 nozzle",
    "from": "system",
    "instantiation": "true",
    "inherits": "fdm_elegoo_common",
    "printer_model": "Elegoo Neptune 2D",
    "default_print_profile": "0.20mm Standard @Elegoo Neptune2D",
    "extruder_colour": [
        "#FCE94F",
        "#FCE94F"
    ],
    "extruder_offset": [
        "0x0",
        "0x0"
    ],
    "nozzle_diameter": [
        "0.4",
        "0.4"
    ],
    "printable_area": [
        "0x0",
        "220x0",
        "220x220",
        "0x220"
    ],
    "printable_height": "250",
    "nozzle_type": "hardened_steel",
    "auxiliary_fan": "0",
    "machine_max_acceleration_extruding": [
        "500",
        "500"
    ],
    "machine_max_acceleration_retracting": [
        "1000",
        "1000"
    ],
    "machine_max_acceleration_travel": [
        "500",
        "500"
    ],
    "machine_max_acceleration_x": [
        "500",
        "500"
    ],
    "machine_max_acceleration_y": [
        "500",
        "500"
    ],
    "machine_max_acceleration_z": [
        "100",
        "100"
    ],
    "machine_max_speed_e": [
        "60",
        "60"
    ],
    "machine_max_speed_x": [
        "500",
        "500"
    ],
    "machine_max_speed_y": [
        "500",
        "500"
    ],
    "machine_max_speed_z": [
        "10",
        "10"
    ],
    "machine_max_jerk_e": [
        "5",
        "5"
    ],
    "machine_max_jerk_x": [
        "8",
        "8"
    ],
    "machine_max_jerk_y": [
        "8",
        "8"
    ],
    "machine_max_jerk_z": [
        "0.4",
        "0.4"
    ],
    "max_layer_height": [
        "0.32",
        "0.32"
    ],
    "min_layer_height": [
        "0.08",
        "0.08"
    ],
    "printer_settings_id": "Elegoo",
    "retraction_minimum_travel": [
        "2",
        "2"
    ],
    "retract_before_wipe": [
        "70%",
        "70%"
    ],
    "retraction_length": [
        "5",
        "5"
    ],
    "retraction_speed": [
        "60",
        "60"
    ],
    "retract_length_toolchange": [
        "1",
        "1"
    ],
    "deretraction_speed": [
        "40",
        "40"
    ],
    "single_extruder_multi_material": "1",
    "change_filament_gcode": "",
    "machine_pause_gcode": "M0",
    "default_filament_profile": [
        "Generic PLA @Elegoo"
    ],
    "machine_start_gcode": "T[initial_tool] ; set active extruder\nM413 S0 ; disable Power Loss Recovery\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM140 S[bed_temperature_initial_layer_single] ; set final bed temp\nM104 S150 ; set temporary nozzle temp to prevent oozing during homing and auto bed leveling\nG4 S10 ; allow partial nozzle warmup\nG28 ; home all axis\n;G29 ; auto bed levelling - remove ; at beginning of line to enable\n;M420 S1 ; enable mesh - remove ; at beginning of line to enable\nG1 Z50 F240\nG1 X2 Y10 F3000\nM104 S[nozzle_temperature_initial_layer] ; set final nozzle temp\nM190 S[bed_temperature_initial_layer_single] ; wait for bed temp to stabilize\nM109 S[nozzle_temperature_initial_layer] ; wait for nozzle temp to stabilize\nG1 Z0.28 F240 ; move down to prime nozzle\nG92 E0 ; reset extruder\nG1 E90 ; load filament\nG92 E0 ; reset extruder\nG1 Y140 E10 F1500 ; prime the nozzle\nG1 X2.3 F5000 ; move over for second prime line\nG92 E0 ; reset extruder\nG1 Y10 E10 F1200 ; prime the nozzle\nG92 E0 ; reset extruder",
    "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\nG1 E-80 F2000 ; unload filament\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < printable_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors",
    "before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n",
    "layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]",
    "scan_first_layer": "0"
}