orcaslicer/resources/profiles/Elegoo/machine/Elegoo Neptune 4 Max (0.6 nozzle).json

{
	"type": "machine",
	"setting_id": "GM001",
	"name": "Elegoo Neptune 4 Max (0.6 nozzle)",
	"from": "system",
	"instantiation": "true",
	"inherits": "fdm_neptune_4_common",
	"printer_model": "Elegoo Neptune 4 Max",
	"printer_notes": "",
	"default_print_profile": "0.20mm Standard @Elegoo Neptune4Max (0.6 nozzle)",
	"nozzle_diameter": [
		"0.6"
	],
	"printer_variant": "0.6",
	"printable_area": [
		"0x0",
		"420x0",
		"420x420",
		"0x420"
	],
	"machine_max_speed_x": [
		"300",
		"300"
	],
	"machine_max_speed_y": [
		"300",
		"300"
	],
	"printable_height": "480",
	"nozzle_hrc": "0",
	"nozzle_type": "brass",
	"nozzle_volume": "0",
	"cooling_tube_length": "5",
    "cooling_tube_retraction": "91.5",
	"enable_filament_ramming": "1",
	"parking_pos_retraction": "92",
	"auxiliary_fan": "1",
	"extra_loading_move": "-2",
    "extruder_clearance_height_to_lid": "34",
    "extruder_clearance_height_to_rod": "34",
    "extruder_clearance_radius": "47",
    "extruder_colour": ["#FCE94F"],
    "extruder_offset": ["0x0"],
	"fan_kickstart": "0",
    "fan_speedup_overhangs": "1",
    "fan_speedup_time": "0",
	"gcode_flavor": "klipper",
	"high_current_on_filament_swap": "0",
	"host_type": "octoprint",
	"machine_load_filament_time": "0",
	"machine_unload_filament_time": "0",
	"max_layer_height": [
		"0.48"
	],
	"min_layer_height": [
		"0.15"
	],
	"printer_settings_id": "Elegoo",
	"retract_before_wipe": ["85%"],
	"retract_length_toolchange": ["2"],
	"deretraction_speed": ["45"],
	"retract_lift_above": ["0"],
    "retract_lift_below": ["0"],
    "retract_lift_enforce": ["All Surfaces"],
    "retract_restart_extra": ["0"],
    "retract_restart_extra_toolchange": ["0"],
    "retract_when_changing_layer": ["1"],
    "retraction_length": ["0.7"],
    "retraction_minimum_travel": ["1"],
    "retraction_speed": ["60"],
	"use_firmwware_retraction": "0",
	"single_extruder_multi_material": "1",
	"use_relative_e_distances": "1",
	"wipe": ["1"],
    "wipe_distance": ["1"],
    "z_hop": ["0.4"],
    "z_hop_types": ["Normal Lift"],
	"change_filament_gcode": "",
	"machine_pause_gcode": "M0",
	"default_filament_profile": [
		"Elegoo Generic PLA @0.6 nozzle"
	],
	"machine_start_gcode": "M413 S0 ; disable Power Loss Recovery\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S120 ; set temporary nozzle temp to prevent oozing during homing and auto bed leveling\nM140 S[bed_temperature_initial_layer_single] ; set final bed temp\nG4 S10 ; allow partial nozzle warmup\nG28 ; home all axis\nG1 Z50 F240\nG1 X2 Y10 F3000\n\nM190 S[bed_temperature_initial_layer_single] ; wait for bed temp to stabilize\nM109 S[nozzle_temperature_initial_layer] ; wait for nozzle temp to stabilize\nG1 Z0.28 F240\nG92 E0\nG1 Y140 E10 F1500 ; prime the nozzle\nG1 X2.3 F5000\nG92 E0\nG1 Y10 E10 F1200 ; prime the nozzle\nG92 E0",
	"machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X10 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+10, printable_height-10)} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors",
	"before_layer_change_gcode": ";BEFORE_LAYER_CHANGE\nG92 E0\n;[layer_z]\n\n",
	"layer_change_gcode": ";AFTER_LAYER_CHANGE\n;[layer_z]",
	"scan_first_layer": "0"
}