"machine_end_gcode":"; printing object ENDGCODE\nG92 E0.0 ; prepare to retract\nG1 E-6 F3000; retract to avoid stringing\n; Anti-stringing end wiggle\n{if layer_z < max_print_height}G1 Z{min(layer_z+100, max_print_height)}{endif} F4000 ; Move print head up\nG1 X0 Y120 F3000 ; present print\n; Reset print setting overrides\nG92 E0\nM200 D0 ; disable volumetric e\nM220 S100 ; reset speed factor to 100%\nM221 S100 ; reset extruder factor to 100%\n;M900 K0 ; reset linear acceleration(Marlin)\n; Shut down printer\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nM18 S180 ;disable motors after 180s\nM300 S40 P10 ; Bip\nM117 Print finish.",
"machine_max_acceleration_e":[
"5000",
"5000"
],
"machine_max_acceleration_extruding":[
"5000",
"2000"
],
"machine_max_acceleration_retracting":[
"5000",
"5000"
],
"machine_max_acceleration_travel":[
"3000",
"3000"
],
"machine_max_acceleration_x":[
"5000",
"2000"
],
"machine_max_acceleration_y":[
"5000",
"2000"
],
"machine_max_acceleration_z":[
"1500",
"200"
],
"machine_max_jerk_e":[
"2.5",
"2.5"
],
"machine_max_jerk_x":[
"9",
"9"
],
"machine_max_jerk_y":[
"9",
"9"
],
"machine_max_jerk_z":[
"3",
"0.4"
],
"machine_max_speed_e":[
"30",
"25"
],
"machine_max_speed_x":[
"300",
"200"
],
"machine_max_speed_y":[
"300",
"200"
],
"machine_max_speed_z":[
"20",
"12"
],
"machine_min_extruding_rate":[
"0",
"0"
],
"machine_min_travel_rate":[
"0",
"0"
],
"machine_pause_gcode":"M600",
"machine_start_gcode":";STARTGCODE\nM117 Initializing\n; Set coordinate modes\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\n; Reset speed and extrusion rates\nM200 D0 ; disable volumetric E\nM220 S100 ; reset speed\n; Set initial warmup temps\nM117 Nozzle preheat\nM104 S100 ; preheat extruder to no ooze temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed final temp\nM300 S40 P10 ; Bip\n; Home\nM117 Homing\nG28 ; home all with default mesh bed level\n; For ABL users put G29 for a leveling request\n; Final warmup routine\nM117 Final warmup\nM104 S[first_layer_temperature] ; set extruder final temp\nM109 S[first_layer_temperature] ; wait for extruder final temp\nM190 S[first_layer_bed_temperature] ; wait for bed final temp\nM300 S440 P200 ; 1st beep for printer ready and allow some time to clean nozzle\nM300 S0 P250 ; wait between dual beep\nM300 S440 P200 ; 2nd beep for printer ready\nG4 S10 ; wait to clean the nozzle\nM300 S440 P200 ; 3rd beep for ready to start printing\n; Prime line routine\nM117 Printing prime line\n;M900 K0; Disable Linear Advance (Marlin) for prime line\nG92 E0.0; reset extrusion distance\nG1 F3000 Z1\nG1 X-150 Y0 Z0.4\nG92 E0\nG3 X0 Y-130 I150 Z0.3 E30 F2000\nG92 E0.0 ; reset extrusion distance\n; Final print adjustments\nM117 Preparing to print\n;M82 ; extruder absolute mode\nM221 S{if layer_height<0.075}100{else}95{endif}\nM300 S40 P10 ; chirp\nM117 Print [input_filename_base]; Display: Printing started...",
